| Common Concours Part Numbers | |||
| Generic and OEM | |||
| Table of Contents: | |||
| Disclaimers and other rubbish | |||
| Other places to look for information | |||
| Original Equipment Parts & Substitutes List | |||
| Accessories: both Factory and Aftermarket | |||
| Aftermarket Clothing | |||
| Givi Replacement Keys | |||
| Common Body Parts & Upgrades | |||
| DISCLAIMER: THESE PART NUMBERS HAVE BEEN CHECKED FOR ACCURACY, BUT AS ALWAYS, MISTAKES MAY OCCUR. VERIFY THAT THE PART MATCHES YOUR OLD PART BEFORE INSTALLATION! | |||
| This list was started by Bryan Moody but hadn't been updated for a couple years. I'm taking it up (NOV2010), but like Bryan said this can't be done without everyone's inputs! If you have any part numbers you would like to contribute, message me (mdr) at either the concours.org or cog-online.org forums. Sorry no email here. I'm hiding from the Spam Crawlers. | |||
| VAST amounts of information are located here: | |||
| ZG/GTR Fanatics Forum | |||
| Concours Owners Group Forums - the Official COG Club Forums | |||
| Bryan's Tech Page - defunct but at archive.org | |||
| David Morrow's Tech Page - defunct but at web.archive.org | |||
| For any OEM parts not listed here try BuyKawasaki.com | |||
| Try your dealer first, but when that fails where *I* go for OE parts and accessories. There are LOTS of others too. | |||
| Ron Ayers Motorsports - Genuine Kawasaki Parts and Fisches with a disount of list price | |||
| Bike Bandit - They have a discount for AMA members | |||
| Orignal Equipment Parts Cross List | |||
| SYSTEM | DESCRIPTION | GENERIC | KAWASAKI |
| SERVICE MANUAL | None Available | 99924-1065-9 | |
| Have this in hand BEFORE starting work! | |||
| brakes | ring, brake piston seal (front & rear) | 43049-002 | |
| brakes | packing, brake piston (front & rear) | 43049-1028 | |
| brakes | front master cylinder cover | 43026-1052 | |
| also used on clutch side | |||
| brakes | front master cylinder cover diaphragm | 43028-1058 | |
| also used on clutch side | |||
| cables | cable, speedometer drive | Dennis Kirk (Motion Pro) Part # C9059 | 54001-1119 |
| cables | cable, throttle closing | 54012-1303 | |
| cables | cable, throttle opening | 54012-1302 | |
| chassis | bag antler (bag stay), LH | 35011-1300 | |
| chassis | bag antler (bag stay), RH | 35011-1301 | |
| chassis | bag keys "A" | 27008-1127-AA | |
| chassis | bag keys "B" | 27008-1127-BB | |
| chassis | bearing, steering head LOWER | 92116-1009 | |
| chassis | bearing, steering head UPPER | Parts Plus: SSK902 (Rick Nolan) | 92116-1056 |
| (25mm bore x 47mm OD x 15mm wide) | BCA (Federal Mogul): 32005 (Rick Hall) | ||
| Bower: 32005 | |||
| get at any bearing supply | |||
| (see note #1) | |||
| chassis | bearing, front wheel 86-93 | 6302 double seals, get at any bearing supply | 601B6302U |
| (15mm bore x 42mm OD x 13mm wide) | (see note #1) | ||
| chassis | bearing, front wheel 94-up | 6203 double seals, get at any bearing supply | 601B6304UU |
| (17mm bore x 40mm OD x 12mm wide) | (see note #1) | ||
| chassis | bearing, rear wheel (all years) | 6304 double seals, get at any bearing supply | 601B6304ZZ |
| (20mm bore x 52mm OD x 15mm wide) | (see note #1) | ||
| chassis | bearing, swingarm | Federal Mogul: 32004 | 92116-1061 |
| tapered roller bearing single row | NSK: 32004 | ||
| (20mm bore x 42mm OD x 15mm wide) | Bower: 32004 | ||
| get at any bearing supply | |||
| (see note #1) | |||
| chassis | collar, | 92027-1935 | |
| metal collar that goes under mounting screws on belly pan | |||
| chassis | flap, side cowling | 35019-1193 | |
| LH (fairing extender) WINTER | |||
| chassis | flap, side cowling | 35019-1194 | |
| RH (fairing extender) WINTER | |||
| chassis | trim, inner cowling | 53044-1184 | |
| quantity 2 | |||
| use w/winter side cowling | |||
| (these are rubber seals that fit between the side cowling and the fairing). | |||
| chassis | fairing extender KIT | K99996-1103 | |
| Includes both above cowlings and inner trim | |||
| Less expensive than buying parts separately | |||
| chassis | final drive, propeller shaft coupler | approximately 32mm ID x 3.5mm thick | 92055-1646 |
| o-ring (2) | |||
| chassis | footpeg bracket, LH | 34003-1259 | |
| chassis | footpeg bracket, RH | 34003-1260 | |
| chassis | footpeg feelers (bank sensor) | 92043-1219 | |
| chassis | footpeg, LH (metal only) | 34028-1198 | |
| chassis | footpeg, RH (metal only) | 34028-1199 | |
| chassis | fork bushings | 44065-1085 | |
| chassis | fork bushing, inner | 44065-1081 | |
| chassis | fork circlips (fit above seals) | 92033-1036 | |
| chassis | fork seals, inner | 92049-1273 | |
| chassis | fork seals, outer (dust cover) | 92093-1232 | |
| chassis | mirror, LH | Replacement glass only, convex (cut to fit) G.M. PN# 15635578 (James Freeman) | 56001-1333 |
| chassis | mirror, RH | Replacement glass only, convex (cut to fit) G.M. PN# 15635578 (James Freeman) | 56001-1334 |
| chassis | plug, (plastic) for allen head bolts | 92066-1216 | |
| chassis | reflector, reflex (for saddlebag) | 28012-1077 | |
| chassis | shift lever pedal assy. | 13242-1213 | |
| chassis | shift lever rubber cover | 92075-1175 | |
| chassis | shock-all years | Progressive Suspension: 420-1016 | 45014-1340 |
| chassis | speedometer drive assy | 41078-1061 | |
| chassis | spring, fork-all years | Progressive Suspension: 11-1102 | 44026-1340 |
| (86-93) | |||
| chassis | rear suspension link seal | 92049-1109 | |
| chassis | trim, inner cowling | 53044-1184 | |
| quantity 2 use w/winter side cowling | |||
| chassis | valve stem, tire 90 degree | 16126-1191 | |
| reccomended on rear wheel for gauge access | |||
| chassis | valve stem, tire straight | 16126-1136 | |
| electrical | alternator rectifier | 13091-1329 | |
| electrical | battery 12V18AH | Exide: 18LA (Will Brown) | 26012-1130 |
| 7 1/8" L x 3 5/8" W x 6 7/16" H | Hawker Odessey: PC680 (Mark Cipriano) | ||
| Interstate: 18LA (Will Brown) | |||
| Sears Diehard: 44071 (Kevin Arnold) | |||
| Super Crank: 18LA (Kevin Arnold) | |||
| Westco: 12V20L (Mark Cipriano) | |||
| Yuasa: YB18L-A | |||
| Sealed Battery: | |||
| Yuasa: YTX20L-BS | |||
| electrical | brush, alternator | 21039-1052 | |
| electrical | brush, starter motor | 21039-1053 | |
| electrical | junction box | 59416-1060 | |
| electrical | junction box relays | Aromat: JS1E-12V | |
| SPDT, 5 amp DC contact rating | NTE: R46-5D3-12 | ||
| 12 VDC coil | (NTE is a nationally distributed replacement parts brand, try your local electronic part house or http://www.mouser.com ) | ||
| thanks to Rick Nolan for the NTE number | |||
| electrical | key blank | Ilco: KA14 | 27008-1103 |
| Taylor: X103 | |||
| electrical | lamp, headlamp bulb, 100/80 | NAPA: BP1210/H4 ($10.99) | 92069-1002 |
| electrical | headlamp socket | NAPA LS 6235 (bakelite) (Jim Dickinson) | |
| or 1984 Honda Accord | |||
| get from junkyard, will not melt when used with high wattage bulbs | |||
| SEE NOTE 2 BELOW | |||
| electrical | headlight | 85-87 ZX600 | 23007-1132 |
| 87-88 ZX1000 | |||
| 89-90 ZX10 | |||
| electrical | lamp, taillamp 12V 27/8W | 1157 | 92069-059 |
| electrical | lamps, clock 12V3W T-7 | 74 (Guy B. Young II) | 92069-1020 |
| electrical | lamps, dash 12V 3.4W | 194, Suggest Sylvania:194LL (long life) | 92069-1007 |
| electrical | lamp, front running light/turn 32/3CP (23/8W) | 1157 | 92069-060 |
| electrical | lamp, rear turn signal 32CP (23W) | 1156 | 92069-055 |
| electrical | switch, cooling fan | ACDelco: E-1858 | 27010-1202 |
| Auto Tune: PT2628 | |||
| Also used on 1991 Honda Civic DX | Beck/Arnley WorldParts: 201-0817 | ||
| Beck/Arnley WorldParts: 201-1369 | |||
| Borg Warner: TFS500 (Tom Masterson) | |||
| Echlin (NAPA): FS-130 | |||
| Facet: FS8404 (Chris Roy) | |||
| Filko: TFS-1 (Bob Chappell) | |||
| Four Seasons: 35934 (Bob Chappell) | |||
| G.P. (?): 40-5001 | |||
| Kem: TW-65 | |||
| Mitech: TS-84 | |||
| Motorcraft: no interchange | |||
| Niehoff: WA-639B | |||
| Standard: TS-84 | |||
| Wells: SW504 (Guy B. Young II) | |||
| electrical | switch, ignition | 27005-5064 | |
| electrical | turn signal flasher unit | Tridon-Stant: EP34 (Guy Young) | 27002-1060 |
| electrical | switch, kickstand (86) | 27010-1214 | |
| electrical | switch, kickstand (87 up) | 27010-1220 | |
| electrical | switch, neutral (gasket 92065-058) | 13151-1080 | |
| electrical | wiring harness '86 | 26001-1773 | |
| (superseded by below) | |||
| electrical | wiring harness '87 to '91 | 26001-1838 | |
| electrical | wiring harness '90-93 | 26030-1038 | |
| electrical | wiring harness '94-up | 26030-1252 | |
| electrical | wiring harness (front) 86-93 | 26001-1774 | |
| electrical | wiring harness (front) 94-up | 26030-1285 | |
| engine | clutch nut | 92015-1929 | |
| MUST be used with the new star springs | |||
| engine | clutch star spring, 2 required | 39130-1071 | |
| (be sure to replace the nut at the same time) | |||
| engine | clutch pushrod seal | Chicago Rawhide (SKF) 3077 | 92049-1165 |
| 8mm ID, 18mm OD, 7mm wide | |||
| get at any bearing supply | |||
| engine | counterbalancer seal | Chicago Rawhide (SKF) 7202 | 92049-1174 |
| 19mm ID, 27mm OD, 5mm wide | |||
| get at any bearing supply | |||
| engine | filter, air | K&N: KA9084 (Rich Doell) | 11013-1112 |
| UNI: NU-2359 (Mark Randol) | |||
| Hiflofiltro: HFA2705 (Mark Randol) | |||
| EMGO: 12-92910 (Mark Randol) | |||
| engine | filter, oil | CarQuest: 89941 (Will Perkins) | 16099-003 |
| Emgo: 10-37500 (Dave Mamanakis) | |||
| Fram: CH6012 | |||
| Hastings: LF571 (John Hinton) | |||
| Honda: 15410-300-024 (Dave Mamanakis) | |||
| Honda: 15410-426-010 (Dave Mamanakis) | |||
| NAPA: 4941 (Dave Mamanakis) | |||
| Perf-Form: J-501 (Dave Mamanakis) | |||
| Purolator: ML16812 (Dale Horstman) | |||
| STP: SMO-12 (Kevin Cummings) | |||
| Triumph: 1210031 (Dave Mamanakis) | |||
| Vesrah: SF-4004 (Doug Donner) | |||
| WIX: 24941 (David Ritchie) | |||
| Yamaha: 36Y-13441-00 (Dave Mamanakis) | |||
| engine | filter, oil | 92022-1012 | |
| Flat washer that goes on top of spring | |||
| (you know, the part that always gets lost) | |||
| 20.5mm id X 30mm od X 1mm thk. | |||
| engine | gasket, engine side cover, RH | 11009-1860 | |
| engine | gasket, neutral safety switch | 92065-058 | |
| engine | gasket, reed valve | 11009-1379 | |
| engine | gasket, pulsing cover (left side) | 11060-1695 | |
| engine | gasket, valve cover | 11009-1378 | |
| engine | gasket, valve cover spark plug well | 11009-1377 | |
| engine | radiator cap | Carquest :33028 (Guy B. Young II) | 49085-1053 |
| (32mm ID x 16mm deep neck) | Stant: 10227 (boxed) (Guy B. Young II) | ||
| 0.9bar / 13psi | Stant: 11227 (blister pack) (Guy B. Young II) | ||
| Same as 1978 Ford Fiesta | Stant: 10229 (Bryan Moody) | ||
| CST: 7013 (Bryan Moody) | |||
| Motorcraft: RS62 (Bryan Moody) | |||
| Motorcraft: RC19 (Bryan Moody) | |||
| Beck/Arnley: 133-8060 (Bryan Moody) | |||
| Beck/Arnley: 133-8078 (Bryan Moody) | |||
| Gates: 31527 (Bryan Moody) | |||
| AC-Delco: RC19 (Bryan Moody) | |||
| engine | shift lever (to transmission shaft) | 13242-1195 | |
| THIS IS THE ONE THAT USUALLY BREAKS | |||
| engine | spark plugs, platinum | NGK: D8EVX | |
| engine | spark plugs, standard | NGK: D8EV | 92070-1011 |
| ACDelco: R121XLS | |||
| engine | spark plug cap | 21160-1065 | |
| engine | thermostat | ACDelco: 131-17 | 49054-1051 |
| Carquest: 31068 (Guy B. Young II) | (old) | ||
| Size AS568-138, aka size 138 | Caterpillar: 272-2538 EPDM (Nathan Wells) | ||
| Caterpillar: 127-8586 NBR (Nathan Wells) | |||
| Also used on 1983 Honda Accord | Futaba: R124 (Kevin Arnold) | 49054-0003 | |
| Mitsubishi: MB221855 (Kevin Arnold) | (new?) | ||
| NAPA: 142 (Guy B. Young II) | |||
| Pep Boys: 29368 (Guy B. Young II) | |||
| Stant: 13368 (boxed) (Guy B. Young II) | |||
| Stant: 35368 (blister pack) (Guy B. Young II) | |||
| Toyota: 16401-63010 (Kevin Arnold) | |||
| engine | thermostat o-ring | McMaster-Carr | 92055-112 |
| 32mm OD x 25mm ID x 3 mm | (viton) Part # 9263K275 | ||
| (buna-n) Part # 9262K275 | |||
| engine | valve cover, Europe/Canada model | 14024-1082 | |
| (does not have provision for reed valves) | |||
| engine | washer, head cover bolt | 92022-1487 | |
| (the cup shaped washer that the valve cover bolts go thru) | |||
| engine | Water Pump Rebuild Kit | K&L: 15-4343 | |
| engine | water pump oil seal | Chicago Rawhide (SKF): 4752 | 92049-1416 |
| 12mm ID x 28mm OD x 7mm wide (Mark Cipriano) | |||
| engine | water pump external pump o-ring, 33mm | 92055-1266 | |
| engine | water pump impeller Cover o-ring | 92055-1271 | |
| fuel | carb bowl o-ring | 92055-1222 | |
| fuel | carb needle (float valve) clamp | 16044-007 | |
| fuel | carb needle (float valve) | 16030-1007 | |
| fuel | petcock to tank o-ring | 51039-010 | |
| fuel | petcock lever o-ring | 92055-1027 | |
| fuel | petcock assy. (complete) | 51023-1130 | |
| fuel | petcock diaphagm cover | 16146-1005 | |
| fuel | petcock diaphragm assy. | 43028-1015 | |
| fuel | petcock diapragm o-ring | 670B1504 | |
| fuel | petcock lever spring | 92081-1171 | |
| tools | Microfiche ZG1000A1-A3 | Why buy it? | 99961-0211 |
| (covers 86-88 models) | Go to BuyKawasaki.com | ||
| or Ron Ayers.com | |||
| tools | Hex Drive Socket | McMaster-Carr | |
| (12mm 1/2" Drive) | Part # 5571A68 | ||
| fits front axle | |||
| tools | Hex Key (12mm Long Arm) | McMaster-Carr | |
| fits front axle | Part # 6958A19 | ||
| tools | Socket 27mm | McMaster-Carr | |
| fits rear axle and rear drive fill plug | Part # 7149A29 ea. | ||
| (1/2" drive) | |||
| tools | Wrench, spanner-steering head | McMaster-Carr | |
| Metric Fixed Head Hook Style Spanner Wrench For 40-42mm Circle Dia | Part #6975A16 | ||
| tools | ABS Cement-used for repairing broken body panels | McMaster-Carr | |
| Part # 74605A85 (8 oz) | |||
| Part # 74605A51 (16 oz) | |||
| Part # 74605A52 (32 oz) | |||
| Note #1: online bearing and seal sales atA&W Bearing or Johnson Bearing | |||
| Note #2: Be sure to check that the female sockets in the plug are TIGHT on the bulb. I have had problems with this and burnt up the NAPA plug. | |||
| ACCESSORIES | |||
| Adventure Motostuff | My favorite general motorcycle stuff seller | ||
| Buck Sport Touring (Larry Buck) | Purveyor of fine products for the C10 and C15 Concours. Lightbars, touring pegs, helmet relocation brackets, conspicuity products, racks, CB mounts. | ||
| Bryan Moody - archive only | Fuel cell kits, Rifle windshield shelving system | ||
| MC Enterprises | Unique motorcycle accessories such as training wheels (smaller bikes), lights and Canyon Cage tip over bars for C14 and soon (DEC2013) the C10. | ||
| Murphs' Kits | Unique products for the C10, C14 and other makes and models | ||
| Sampson Sport Touring | Fuel cells, luggage racks | ||
| Shoodaben Engineering | 'Hot rod' and reliability mods for the C10. Also performs full carburetor rehabs. You send 'em, he cleans and jets and... | ||
| Givi Key Info | |||
| Givi Replacement keys are available from most lock shops. Use an ILCO X226/HYD12 blank (Dr. Squido Calamari) | |||
| Common Body Parts & Upgrades | |||
| Factory extended windshield | K53020-083 | ||
| Factory trim for above | 53044-1196 | ||
| Factory luggage rack | K53020-083 | ||
| Factory Backrest and pad 86-93 models | K53043-052 | ||
| Factory Backrest and pad 94-present models | K53043-052A | ||
| Factory adaptor to mount backrest and pad to luggage rack | K53021-083 | ||
| Factory saddlebag liners Black/Red | K99994-335 | ||
| Factory saddlebag Liners Black/Gray | K99994-337 | ||
| Factory Air Deflectors (similar to Baker Air Wings) | K53003-020 | ||
| Factory Fairing Extender Kit (contains both side extensions and trim) | K99996-1103 | ||
| Factory Tank Bra | K99994-918 | ||
| Jet Kit by Factory Pro | K21 | ||
| Rifle Windshield system | http://www.rifle.com | ||
| Rifle base ONLY | 0.201.1116 | ||
| Rifle windshield ONLY 15" clear | 0.211.0001 | ||
| Rifle windshield ONLY 17" clear | 0.211.0002 | ||
| Rifle windshield ONLY 19" clear | 0.211.0003 | ||
| Rifle windshield ONLY custom | 0.211.0004 | ||
| Rifle windshield ONLY 15" tinted | 0.211.0011 | ||
| Rifle windshield ONLY 17" tinted | 0.211.0012 | ||
| Rifle windshield ONLY 19" tinted | 0.211.0013 | ||
| Rifle windshield ONLY custom | 0.211.0014 | ||
| Baker Air Wings-the genuine article | CONAW | ||
| http://www.bakerbuilt.com/ | |||
| Race Tech Cartridge Emulators (94 up) | FEGVS3801 | ||
| BMW Type Electrical Connector (John Deere) | RE11344 PLUG | ||
| AL25073 SOCKET | |||
| BACK TO THE CONCOURS TECH PAGE | |||